smartctl 7.3 2022-02-28 r5338 [FreeBSD 13.1-RELEASE-p8 amd64] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     ADATA SU700
Serial Number:    --
LU WWN Device Id: 5 707c18 ...
Firmware Version: B170206b
User Capacity:    120,034,123,776 bytes [120 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
TRIM Command:     Available, deterministic, zeroed
Device is:        Not in smartctl database 7.3/5319
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Jul 11 18:56:13 2023 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(   33) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (   1) minutes.
Conveyance self-test routine
recommended polling time: 	 (   1) minutes.
SCT capabilities: 	       (0x0039)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  9 Power_On_Hours          -O--C-   100   100   000    -    31425
 12 Power_Cycle_Count       -O--C-   100   100   000    -    264
167 Unknown_Attribute       -O---K   100   100   000    -    0
168 Unknown_Attribute       -O--C-   100   100   000    -    0
169 Unknown_Attribute       PO--C-   100   100   010    -    0
173 Unknown_Attribute       -O--C-   200   200   000    -    11983847863
175 Program_Fail_Count_Chip PO--C-   100   100   010    -    0
180 Unused_Rsvd_Blk_Cnt_Tot PO--CK   100   100   020    -    456
192 Power-Off_Retract_Count -O--C-   100   100   000    -    0
194 Temperature_Celsius     -O---K   053   053   030    -    47 (Min/Max 47/47)
231 Unknown_SSD_Attribute   PO--CK   086   086   005    -    14
233 Media_Wearout_Indicator -O--CK   100   100   000    -    34455115264
234 Unknown_Attribute       -O--CK   100   100   000    -    15215950888960
241 Total_LBAs_Written      -O--CK   100   100   000    -    23419339072
242 Total_LBAs_Read         -O--CK   100   100   000    -    4715942667
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O     51  Comprehensive SMART error log
0x03       GPL     R/O     64  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
Device Error Count: 2875 (device log contains only the most recent 256 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 2875 [58] occurred at disk power-on lifetime: 18825 hours (784 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 00 00 00 a0 08  Error: UNC at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 00 00 1d 53 00 e9 08 20d+22:54:41.812  READ DMA
  ca 00 00 00 08 00 00 00 00 08 00 e0 08 20d+22:54:41.812  WRITE DMA
  ef 00 10 00 03 00 00 00 00 00 00 a0 08 20d+22:54:41.812  SET FEATURES [Enable SATA feature]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08 20d+22:54:41.812  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:41.812  IDENTIFY DEVICE

Error 2874 [57] occurred at disk power-on lifetime: 18825 hours (784 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 a8 00 00 0d f7 47 c8 40 08  Error: UNC at LBA = 0x0df747c8 = 234309576

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 d8 00 00 09 1d 53 00 40 08 20d+22:54:36.212  READ FPDMA QUEUED
  ef 00 10 00 03 00 00 00 00 00 00 a0 08 20d+22:54:36.112  SET FEATURES [Enable SATA feature]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08 20d+22:54:36.112  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:36.112  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08 20d+22:54:36.112  SET FEATURES [Set transfer mode]

Error 2873 [56] occurred at disk power-on lifetime: 18825 hours (784 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 78 00 00 00 00 08 00 40 08  Error: UNC at LBA = 0x00000800 = 2048

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 f0 00 00 09 1d 53 00 40 08 20d+22:54:30.612  READ FPDMA QUEUED
  ef 00 10 00 03 00 00 00 00 00 00 a0 08 20d+22:54:30.512  SET FEATURES [Enable SATA feature]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08 20d+22:54:30.512  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:30.512  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08 20d+22:54:30.512  SET FEATURES [Set transfer mode]

Error 2872 [55] occurred at disk power-on lifetime: 18825 hours (784 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 68 00 00 09 16 79 20 40 08  Error: UNC at LBA = 0x09167920 = 152467744

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 60 00 00 09 1d 53 00 40 08 20d+22:54:25.012  READ FPDMA QUEUED
  e7 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:24.912  FLUSH CACHE
  e7 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:24.912  FLUSH CACHE
  e7 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:24.912  FLUSH CACHE
  ef 00 10 00 03 00 00 00 00 00 00 a0 08 20d+22:54:24.912  SET FEATURES [Enable SATA feature]

Error 2871 [54] occurred at disk power-on lifetime: 18825 hours (784 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 b8 00 00 09 1d 53 b0 40 08  Error: UNC at LBA = 0x091d53b0 = 152916912

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 b0 00 00 09 1d 53 00 40 08 20d+22:54:19.412  READ FPDMA QUEUED
  e7 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:16.412  FLUSH CACHE
  e7 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:16.412  FLUSH CACHE
  e7 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:12.812  FLUSH CACHE
  e7 00 00 00 00 00 00 00 00 00 00 a0 08 20d+22:54:12.612  FLUSH CACHE

Error 2870 [53] occurred at disk power-on lifetime: 8911 hours (371 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 00 71 ca ce e3 00  Error: UNC 8 sectors at LBA = 0x0371cace = 57789134

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 00 00 71 ca c8 e3 08 29d+23:04:48.008  READ DMA
  ef 00 10 00 02 00 00 00 00 00 00 a0 08 29d+23:04:48.008  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08 29d+23:04:48.008  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08 29d+23:04:48.008  SET FEATURES [Set transfer mode]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08 29d+23:04:48.008  SET FEATURES [Enable SATA feature]

Error 2869 [52] occurred at disk power-on lifetime: 8911 hours (371 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 08 00 00 00 71 ca ce e3 00  Error: UNC 8 sectors at LBA = 0x0371cace = 57789134

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 08 00 00 00 71 ca c8 e3 08 29d+23:04:48.008  READ DMA
  ef 00 10 00 02 00 00 00 00 00 00 a0 08 29d+23:04:48.008  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 00 00 00 00 00 a0 08 29d+23:04:48.008  IDENTIFY DEVICE
  ef 00 03 00 46 00 00 00 00 00 00 a0 08 29d+23:04:48.008  SET FEATURES [Set transfer mode]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08 29d+23:04:48.008  SET FEATURES [Enable SATA feature]

Error 2868 [51] occurred at disk power-on lifetime: 8911 hours (371 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 80 00 00 00 71 ca ce e3 00  Error: UNC 128 sectors at LBA = 0x0371cace = 57789134

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  c8 00 00 00 80 00 00 00 71 ca 70 e3 08 29d+23:04:48.008  READ DMA
  c8 00 00 00 70 00 00 00 8f c5 20 e3 08 29d+23:04:47.908  READ DMA
  c8 00 00 00 20 00 00 00 8f c5 00 e3 08 29d+23:04:47.908  READ DMA
  c8 00 00 00 30 00 00 00 cb 09 48 eb 08 29d+23:04:47.908  READ DMA
  c8 00 00 00 20 00 00 00 cb 09 28 eb 08 29d+23:04:47.908  READ DMA

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       1 (0x0001)
Device State:                        Active (0)
Current Temperature:                     ? Celsius
Power Cycle Min/Max Temperature:      ?/ ? Celsius
Lifetime    Min/Max Temperature:      ?/ ? Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -127/127 Celsius
Min/Max Temperature Limit:           -127/127 Celsius
Temperature History Size (Index):    478 (287)

SCT Error Recovery Control:
           Read:     80 (8.0 seconds)
          Write:     80 (8.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  4            0  Transition from drive PhyRdy to drive PhyNRdy
0x000a  4            9  Device-to-host register FISes sent due to a COMRESET
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC

